Involute Gears, Explained
After reading this you can pick a module and tooth count, predict a gear's pitch, outside and root diameters, check whether two gears will mesh at a given centre distance, and tell in advance whether a planetary set will assemble.
What an involute gear is, and one example
A spur gear transmits rotation by pushing tooth against tooth. If the tooth faces were flat, the speed ratio would surge and stall as each tooth slid past. The involute curve fixes that. An involute is the path traced by the end of a taut string as you unwind it from a circle, called the base circle. When two involute flanks roll against each other, the contact point moves along a straight line, and the ratio of the two rotation speeds stays exactly constant.
Here is the hook. Take a 20 tooth pinion driving a 40 tooth gear, both with module m = 2 mm. The pinion turns twice for every single turn of the gear, and it does so smoothly, with no speed ripple, as long as the flanks are true involutes. Change the centre distance by a fraction of a millimetre and the ratio does not change: the involute still rolls cleanly, which is why involute teeth tolerate real manufacturing error.
The Linkage & Mechanism Simulator handles bars and pins; this tool handles the one mechanism where curved surfaces carry the load.
When to use it, and when not
Reach for this tool when you want parts that mesh and you plan to cut them: a laser cutter, a CNC router, a 3D printer, or a CAD model you will refine. It draws a true involute flank with a root fillet and backlash, so the exported outline is the part, not a sketch.
Do not use it to predict strength, wear life or heat. The geometry tells you nothing about the bending stress at the tooth root or the surface fatigue on the flank. Those need a load, a material, and the Lewis and Hertz equations, which this tool does not solve. Treat the output as the shape of a correct gear, not a promise that it will survive your torque.
The tool works at true scale. One millimetre in the drawing is one millimetre on your machine bed, so you can send the SVG or DXF straight to the cutter without rescaling. Check your cutter's units are set to millimetres if you used metric module.
The sizing formulas, with intuition
The module m is the single number that sets a gear's size. It is millimetres of pitch diameter per tooth. Everything else follows from the module, the tooth count z and the pressure angle \alpha.
The pitch diameter is the diameter of the imaginary circle that rolls without slipping against its mate:
Here d is the pitch diameter in millimetres, m the module, and z the number of teeth. A module 2 gear with 20 teeth has d = 40 mm.
The teeth stand one module above the pitch circle and sink 1.25m below it (the extra 0.25 is clearance). So the outside and root diameters are:
d_a is the tip diameter and d_f the root diameter. For the module 2, 20 tooth gear, d_a = 44 mm and d_f = 35 mm.
The base circle, the one the string unwinds from, is smaller than the pitch circle by the cosine of the pressure angle:
With the standard \alpha = 20^\circ, \cos 20^\circ = 0.9397, so a 40 mm pitch circle gives a base circle of d_b = 37.59 mm.
For two meshing gears the centre distance is the sum of the pitch radii:
A 20 tooth pinion and 40 tooth gear at module 2 sit a = 2(20 + 40)/2 = 60 mm apart.
Undercut and profile shift
If a gear has too few teeth, the cutter that shapes it reaches past the base circle and scoops material out of the flank near the root. This is undercut. It weakens the tooth and can remove part of the active flank. The threshold tooth count is:
At \alpha = 20^\circ, \sin 20^\circ = 0.3420, so z_{min} = 2 / 0.3420^2 = 17.1. Any gear below 17 teeth undercuts.
The fix is a profile shift: move the cutter outward by a fraction x of the module. A positive shift of about x = (17 - z)/17 removes the undercut. For a 12 tooth pinion that is x = (17 - 12)/17 = 0.29. The tooth gets thicker at the root and the whole profile moves out, so the outside diameter grows by 2 x m.
If you must run a pinion below 17 teeth, apply a positive shift to the small gear and an equal negative shift to its mate. The centre distance stays standard and both teeth keep full roots.
A worked example: the demo gear pair
Module 2, pressure angle 20 degrees, 20 and 40 teeth
These are the tool's defaults. Work through the pinion, then the gear, then the mesh.
- Pinion pitch diameter: d = 2 \times 20 = 40 mm.
- Pinion outside diameter: d_a = 2(20 + 2) = 44 mm.
- Pinion root diameter: d_f = 2(20 - 2.5) = 35 mm.
- Pinion base circle: d_b = 40 \times 0.9397 = 37.59 mm.
- Gear pitch diameter: d = 2 \times 40 = 80 mm; outside 84 mm; root 75 mm; base 80 \times 0.9397 = 75.18 mm.
- Centre distance: a = 2(20 + 40)/2 = 60 mm.
- Gear ratio: 40/20 = 2.0. The pinion turns twice per gear turn.
Both gears have more than 17 teeth, so neither undercuts. The tool reports these same numbers and draws both flanks true to size.
The chart below shows how the three diameters of a module 2 gear grow with tooth count. The three lines fan out at a fixed spacing because each diameter is linear in z.
Reading the contact ratio
The contact ratio is the average number of tooth pairs sharing the load at any instant. Below 1.0 the gears would separate between teeth and jam. You want at least 1.2, and 1.6 or more is comfortable. It is the length of the line of action divided by the base pitch:
The r_a terms are tip radii, the r_b terms are base radii, a is the centre distance and \pi m \cos\alpha is the base pitch. For the demo pair: tip radii 22 and 42 mm, base radii 18.79 and 37.59 mm, and a\sin\alpha = 60 \times 0.3420 = 20.52. The numerator is \sqrt{484 - 353.1} + \sqrt{1764 - 1413} - 20.52 = 11.44 + 18.73 - 20.52 = 9.65. The base pitch is \pi \times 2 \times 0.9397 = 5.904. So \varepsilon = 9.65 / 5.904 = 1.63. That is a healthy value: on average 1.63 tooth pairs carry the load.
The planetary assembly rule
A planetary set has a central sun, a set of planets, and an outer ring with internal teeth. The geometry only closes when two conditions hold. First, the ring tooth count must equal the sun plus twice the planet:
Second, for the planets to space evenly, the sum of sun and ring teeth must divide by the number of planets N:
Take a sun of 24, planets of 18, and a ring that must therefore be 24 + 2 \times 18 = 60. With 3 planets, (24 + 60)/3 = 28, a whole number, so it assembles. With 4 planets, (24 + 60)/4 = 21, also whole, so that assembles too. With 5 planets, 84/5 = 16.8, not whole, so five evenly spaced planets will not fit.
Both rules must pass. A set can satisfy z_{ring} = z_{sun} + 2z_{planet} and still jam if the planet count does not divide the sum. The tool flags each failure separately, so read both warnings.
Common mistakes
The errors below cost the most cutting time, so check them before export.
- Mixing module and diametral pitch
- Module is metric millimetres per tooth; diametral pitch is imperial teeth per inch. They are reciprocals through 25.4: m = 25.4 / P_d. A gear at
DP 16is module 1.5875, not 16. Set one convention and stay in it. - Meshing gears of different module
- Two gears only mesh if they share the same module and pressure angle. A module 2 and a module 3 gear will clash no matter the tooth counts.
- Ignoring backlash
- If you cut both flanks to exact size, the teeth will bind. A small backlash, typically 0.02 to 0.1 mm, thins each tooth so the pair turns freely. Thermal expansion and cutter kerf make zero backlash impractical.
- Running a pinion below 17 teeth without a shift
- You get undercut, a weak root and a notchy mesh. Apply the profile shift from the earlier section.
Related tools
Once your gears mesh, you often need the rest of the machine. The PID Controller Simulator tunes the feedback loop that drives a geared axis to a target. The Topology Optimizer grows the lightest bracket that holds your gear shafts, and exports SVG or STL like this tool. For the electrical side, the Circuit Simulator lets you build the motor driver on a grid. If the gearbox lives in a vehicle, the Rocket Designer & Staging Lab shows where mechanical ratios meet mass budgets.
Frequently asked questions
What pressure angle should I pick?
Use 20 degrees unless you have a reason not to. It is the global standard, so your gear will mate with stock parts. Choose 14.5 degrees only for legacy compatibility, and 25 degrees when you need stronger teeth at low tooth counts: a higher angle lowers the undercut threshold from 17 to about 11 teeth.
How do I change the gear ratio without changing the module?
Change the tooth counts. The ratio is z_2 / z_1, and both gears keep the same module so they still mesh. To go from 2:1 to 3:1 on a 20 tooth pinion, raise the big gear from 40 to 60 teeth. The centre distance grows from 60 to 80 mm.
Will my laser-cut gears actually spin smoothly?
Often yes, if you add backlash and a root fillet, which the tool does. The main risks are kerf (the laser removes material, thinning teeth further) and flat stock that binds on the shaft. Add 0.05 to 0.1 mm backlash and test-fit the bore before cutting a full set.
Why does my planetary set refuse to assemble?
One of the two rules failed. Either the ring does not equal z_{sun} + 2z_{planet}, or the sum z_{sun} + z_{ring} is not divisible by the planet count. Adjust the planet tooth count to satisfy the first, then the planet number to satisfy the second.
What is the difference between pitch, outside and root diameter?
The pitch diameter d = mz is where the gears roll without slipping and where you measure centre distance. The outside diameter d_a is the tooth tips, 2m larger. The root diameter d_f is the bottom of the tooth gaps, 2.5m smaller than pitch.